Bulk SMS software helps you to send sms from pc using GSM modems. Broadcast notifications and standard messages through USB modem that is connected with your PC. Offer inbuilt list wizard option to manage list of contact numbers to send sms from modem. Provides easy way to send text sms in bulk number via USB modems. SMS Deliverer is a low-cost and extremely effective mass 2-way SMS software which supports various types of GSM dongle/modem and Android cell phones. It allows you to send out bulk SMS messages in one hit via the computer. It can be running as a service providing a phone number you can send any SMS on and get a text of it. Send sms using gsm module and pic microcontroller: this article explains how to send sms using gsm module and pic microcontroller. What is AT commands and their use to send and receive sms. I have already posted a article on gsm module interfacing with pic microcontroller. I suggest you to go through that article before proceeding in this. I need to develop an application that will send bulk sms messages to customers and allow recipients to send sms messages to a number say 1705 that will come through the modem and be parsed into a MS SQL database. I have been advised to use GSM modem and read/write serial ports using C# code. Any suggestions out there?
This is a simple project/tutorial on how to send sms/text message using sim900d gsm module with arduino uno. Project code is written in arduino ide. The code is compatible to all arduino boards. Post covers how to interface sim900 gsm module with arduino uno and efficiently send sms/text message to a desired cell phone number. Sim900d is a system on chip(SOC) by SimCom. Sim900 can work as gsm and gprs module. It also has Input/Output pins for controlling appliances but they are rarely used. Pre-assembled sim900 gsm boards available in market did not expose its gpio pins. Only the gsm and gprs connection pins are present on board(UART port pins Tx and Rx). Sim900d gsm/gprs module works on AT command set. Almost every GSM chip by simcom works on AT command set. An external microcontroller is required to talk to sim900 gsm module. Sim900 communicates with external controller on UART protocol. In uart protocol only two pins are required to talk with external devices Tx(Transmit) and Rx(Receive). Both the devices must have one single uart port to talk with each other. Communication speed in uart protocol is termed as baud rate. We first have to set the baud rate speed of the modules who are going to communicate on uart protocol. Both the modules must be on the same speed for successful communication.
Arduino has a default uart port on its pins#0 and 1. So arduino can talk to devices which requires uart protocol for communication. Arduino Rx or pin#0 is tied to Tx of sim900 module and arduino Tx or pin#1 is tied with Rx of sim900 module for communication.
Coming to wards ‘AT’ command set. Their are numerous ‘AT’ commands if you go through the data sheet of sim900 gsm module. In this tutorial i will explain only the ones which are required to send an sms with gsm sim900 module. If you wan to learn all the commands go through the data sheet of sim900 module. AT commands which are required to send a text message/sms are listed below. .
sim900 gsm module AT command set to send sms text message
The upper few AT commands are required to send an sms with arduino gsm module. We can skip the first command ‘AT’, if we are sure that our module is perfectly operational. ‘AT’ command only checks the status of the gsm module working or not.
First insert your sim in the sim900 module sim slot and be sure you have credit/balance in it for texting to other numbers. Connect Arduino uno Rx(Pin#0) to GSM module TX and TX(Pin#1) of Arduino uno to RX of sim900 GSM module. Sim900 requires about 5 volts and 1 ampere of current while transmitting the sms/text message. We can not power the gsm module directly with the arduino 5v output. External dc adopter which can supply continuous 1 ampere of current at 5 volt is enough for the arduino and sim900 module power requirements. Note: If your GSM stops working and restarts it self when you send commands to it. It means your GSM needs more current. Try to power your circuit with high rating of source like on the right side i powered the diy circuit with 4.5 Ah 5v DC batter. | GSM sim900d with arduino mega and battery-circuit Diagram |
![Send Sms Using Gsm Modem Send Sms Using Gsm Modem](/uploads/1/1/7/8/117802801/609037435.jpg)
You can also use a current booster circuit for your gsm power requirements. You can purchase cheap current booster circuits online from Chinese electric stores. Important: If you are powering both the arduino and sim900 gsm module with different power supplies then you must make the grounds of both the power sources common. In Uart protocol both the modules sender and receiver must be on the same potential. So you have to make both modules ground common.
![Send sms using gsm modem password Send sms using gsm modem password](/uploads/1/1/7/8/117802801/777315426.jpg)
One can use any sim900 gsm module by any vendor/manufacturer to interface it with arduino. The circuit connections will be same as given on the right hand side. |
Pkey button on your GSM is Power button when you press the push button associated with Pkey your GSM module becomes on and starts working. Now when you press it again your GSM becomes off.
Now coming to the code portion of the project. Ccode is written in arduino ide. Code is universal it is compatible with other arduino boards also. You can use it with arduino uno, arduino lenardo, arduino mega and arduino due etc. For arduino mega you have to connect the Rx Tx lines of GSM to UART channel 1 of Arduino Mega. I tested it on both arduino uno and mega. I am sending my website name “www.microcontroller-project.com” as sms/text message to receiver.
In the setup function i first initialized the arduino uart port. Communication baud rate is set to 9600 bps. Sim900 gsm module default baud rate is 9600 bps. So i set the arduino uart baud rate to 9600. Arduino code statement used for this purpose is Serial.begin(9600). In the loop function i am sending one by one each ‘AT’ command discussed above to send a text message with arduino gsm module. To send data with uart of arduino using arduino ide we put our data in Serial.print(“”) command. Our data comes in double quotations. Send Sms Using Gsm Modem For Pc
- Recall that sim900 accepts the cell number of the recipient enclosed in double quotations.
- To send the recipient cell number to sim900 gsm module using arduino ide we must put the ” in the code statement. If we do not put the . Then arduino ide compiler identifies it as the arduino ide statement and executes it rather than sending it on uart to sim900 module. ” tells the arduino ide compiler that “ is data to be send out on uart.
At the end of the code i inserted a while(1) loop. While loop will hold the control for ever. It means our code will execute only once after power up and after than it stops.
Send Sms Using Gsm Modem For Iphone
I made arduino home security system using arduino gsm module, pir motion detector sensor and door contact sensor. Visit the diy project by clicking the below button.